Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Antioch Homeowners Choose Dvele Construction
We provide independent Dvele construction, repair and service in Antioch. What makes our Dvele work different is that we focus on the site side of a factory-built home: the foundation interface, the module seams, the roof tie-ins and the mechanical hookups. That’s where a Dvele home actually lives or dies in the East Bay, and it’s the part the factory can’t control.
Dvele builds single-family modular homes, ADU modules and two-story modular residences as steel-framed boxes completed in a plant and shipped to site. By the time the modules land in Antioch, the factory’s job is done. Yours starts. Our technicians have up to 13 years of experience with residential construction and remodeling, and we handle the finished site work that determines whether a modular home stays tight through a Delta summer and a wet winter.
To be clear: we’re an independent Dvele service provider. We’re not affiliated with or authorized by Dvele, and we don’t speak for the manufacturer. If you own or are planning a Dvele home in Antioch and need the site work done right, call (866) 811-9694. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Construction Antioch for Your Dvele Construction?
Modular construction punishes guesswork. A Dvele home arrives as a nearly finished assembly, and the trades that follow have to work around factory tolerances rather than build from scratch. That’s a different skill set from framing a stick-built house, and it’s the one we bring.
Because Dvele homes are built to order, trim, glazing and hardware are often matched to the factory spec rather than swapped for whatever’s on a shelf. We pay attention to that. We specify quality parts that fit the assembly, document what goes in, and work in a way that respects the factory envelope instead of cutting into it. Where a detail is site-side, like flashing, sealant or trim, we treat it as a targeted repair rather than a reason to open up a factory assembly.
Our scope also matters here. We work across seven trade categories: roofing, kitchens, bathrooms, windows and doors, fencing, pavers, and home additions and ADUs. A Dvele owner who needs a seam re-flashed, a roof edge repaired and a bathroom reworked shouldn’t have to line up three separate contractors who each blame the other. One contractor, every project. We can also work with your insurer when a water intrusion claim is part of the picture.
And we’re honest about the limits. We’re licensed and insured, estimates are free, and your written line-item estimate sets the final price. No change orders once the work starts.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Dvele Construction Problems We Fix in Antioch
These aren’t hypothetical. They’re the recurring issues we see on factory-built modular homes in this climate, and each one traces back to a site condition rather than a manufacturing defect.
- Module-to-module seam caulking and flashing that opens up. Seasonal movement works on the exterior joints where modules meet. The caulk bead fails first, then wind-driven rain finds the gap. In Antioch, where delta breezes off the river push rain sideways against a wall, a joint that’s merely adequate inland becomes a leak here. The repair is to open the joint, check the flashing lap and re-seal to spec, not to smear a new bead over the old one.
- Settlement and shim issues at the marriage line. Where modules meet the site foundation, shims carry real load. Expansive Delta-edge clay soils move with the seasons, and a home that sat level at handover can develop floors that slope or doors that no longer latch squarely at the marriage line. The symptom shows up inside; the cause is usually underneath.
- Roof drainage on the assembled envelope. Gutters and downspouts specified at the module edges can pool water against the fascia or at the roofline once the modules are joined and the roofline is continuous. Water tracking behind fascia is a classic sign. Clearing and correcting drainage comes before any cosmetic fix.
- Unsealed penetrations where site trades tie in. HVAC, plumbing and electrical chases get opened on site. A chase opening that’s poorly sealed becomes an air and moisture leak, and in a hot Antioch summer that’s both a comfort problem and a moisture problem once winter arrives.
- Exterior trim and cladding movement at joint lines. Factory trim meets site-finished edges, and the transition is where paint bubbles and caulk lines crack. Left alone, that small gap lets water behind the cladding.
Here’s how this usually goes for a Dvele homeowner: the problem shows up after the first wet season or a hot summer. A damp stain or bubbling paint at a module seam, a door that won’t close squarely at the marriage line, or water tracking behind the fascia near a roof edge. The usual culprits are a failed sealant joint, a flashing detail that wasn’t lapped correctly at assembly, or slight settlement at the foundation shims. A qualified local pro opens the joint, checks the framing and shims, re-flashes and re-seals to spec, verifies drainage before closing it back up, then confirms the interior side is dry and level.
Antioch’s housing stock makes this sharper. The core of the city is 1950s – 1970s single-story tract homes, and the east side and Hillcrest are 1980s – 2000s subdivisions in stucco. A Dvele home sits among both, sometimes on a lot carved from older ground near the river. That means aging utilities and post-war slab or raised foundations are often nearby, and tie-ins need to be planned around what’s actually there rather than what a drawing assumed.
Dvele Parts & Our Repair-vs-Replace Approach
We don’t stock or sell OEM or genuine Dvele parts, and we’re not a Dvele dealer. What we do is source quality parts that fit your Dvele equipment and match the factory spec closely enough that the envelope still performs the way it was designed to.
That matters most on a built-to-order home. Trim profiles, glazing and hardware are often matched rather than replaced with generic stock, because a cheap aftermarket substitution can change how the assembly handles water, air and heat. A component that’s documented as equivalent is one thing. A component that just happens to fit is another, and on a modular envelope that difference shows up two winters later.
Repair versus replace comes down to where the failure sits. If it’s site-side, meaning flashing, sealant, trim or drainage, targeted repair is almost always the right call. Ripping into a factory assembly to chase a problem that lives at the joint is expensive and unnecessary. If a component is genuinely at the end of its life, we’ll say so and quote the replacement in writing before anything starts.
Call (866) 811-9694 for a free estimate and a straight answer on which way to go.
Our Dvele Service Process – Step by Step
- 1
Diagnosis. We start at the symptom and work outward. A damp stain inside means we’re checking the exterior joint above it, the flashing lap, the shims at the marriage line and the roof drainage on that elevation. On a modular home, the cause is rarely where the stain is.
- 2
Repair or install. We open the joint or chase, inspect the framing and shims, and re-flash and re-seal to spec. Interior work on a Dvele home, like a kitchen or bathroom remodel, is planned around the factory layout and mechanical locations so we’re not cutting into structure we shouldn’t touch.
- 3
Test. We verify drainage before closing anything back up, then confirm the interior side is dry and level. On a plumbing or HVAC tie-in, that means checking the seal at the chase opening, not just whether the fixture works.
- 4
Documentation and warranty. You get a written record of what was done, what parts went in and what was left alone. We can work with your insurer on water intrusion claims, and warranty terms are set out in writing in your estimate before work begins.
See the difference
Before
After
Before
After
Before
AfterDvele Products We Service & Install in Antioch
We service and install site-side work for the kinds of homes Dvele builds: single-family modular homes with steel frames and factory-completed modules, Dvele ADU modules, and two-story modular residences. For each, the work is the same category of craft: foundation interfaces, seam weatherproofing, roof tie-ins, mechanical penetrations and the interior remodeling that follows.
On the remodel side, we handle full kitchen remodeling and full bathroom remodeling inside a Dvele home, plus roof repair and roof replacement on the assembled envelope. We don’t claim to stock Dvele components or to modify the factory-built structure itself. We work with what’s on site and around it. If you’re in Antioch and own a Dvele home, that’s the scope we cover, and we’ll tell you plainly if a job falls outside it.
We Also Service These Brands
We’re not a single-brand shop, and that’s useful when a Dvele remodel turns into a full-house job. We work with more than 50 recognized manufacturers across our trades, including KraftMaid cabinetry, Cambria, Silestone and Kohler fixtures and finishes. Material choice is driven by your priorities, not by what a supplier happens to be pushing that month. For a Dvele owner in Antioch remodeling a kitchen or bath, that means real options at every budget tier.
FAQs – Dvele Construction Service in Antioch
No. We’re an independent Dvele service provider, not affiliated with or authorized by the manufacturer. We handle the site-side construction, repair and remodeling work on Dvele homes in Antioch, and we don’t speak for Dvele or represent their warranty. What we do bring is licensed, insured work, free estimates and a written line-item quote before anything starts.
Yes. Because Dvele homes are built to order, trim, glazing and hardware often need matching to the factory spec rather than a generic substitution. We source quality parts that fit the assembly and document what goes in. We don’t stock or sell OEM or genuine Dvele parts, and we’re not a dealer. We match or use documented-equivalent components so the envelope keeps performing the way it was designed to. Call (866) 811-9694 for a free estimate.
Most site-side repairs, like re-sealing a module seam or correcting a flashing detail, are a one-visit job once the cause is confirmed. Roof repairs and interior remodels take longer and depend on scope. We give you the expected timeline in the written estimate rather than a vague promise, and that estimate sets the final price. For a specific answer on your Dvele home in Antioch, call (866) 811-9694.
We cover the site-side work on Dvele single-family modular homes, Dvele ADU modules and two-story modular residences. That includes foundation interfaces, seam weatherproofing, roof repair and replacement on the assembled envelope, mechanical penetration sealing, and full kitchen and bathroom remodels inside the home. We don’t modify the factory-built structure itself.
We can’t speak for Dvele’s warranty, since we’re independent of the manufacturer. What we can do is work in a way that respects the factory envelope, document every part and procedure, and avoid cutting into factory assemblies where a site-side repair will solve the problem. Keep your documentation, and check your Dvele warranty terms directly with the manufacturer before major work.
Typical estimated ranges for the work most Dvele owners need fall between $400 and $45,000 depending on scope, and your written estimate sets the final price. Site-side repairs sit at the low end and full interior remodels at the high end. Here’s the breakdown:
| Service | Typical Estimated Range |
|---|---|
| Roof Repair | $400 – $1800 |
| Roof Replacement | $8000 – $20000 |
| Full Kitchen Remodel | $14000 – $45000 |
| Small Kitchen Remodel | $9000 – $20000 |
| Full Bathroom Remodel | $9000 – $28000 |
| Walk-In Shower Installation | $4500 – $12000 |
Call (866) 811-9694 for an exact quote. Estimates are free.
Yes, with care. Kitchen and bathroom remodels, flooring and finishes can be done inside a Dvele home without touching the structural modules, as long as the work is planned around the factory layout and the mechanical locations. Anything that involves cutting the structure itself is a different conversation, and we’ll tell you if a job crosses that line. We plan every remodel around the assembly rather than through it.
Almost always a failed sealant joint or a flashing detail that wasn’t lapped correctly when the modules were assembled on site. Seasonal movement opens the caulk bead, and in Antioch the delta breezes off the river drive rain sideways into joints that would stay dry on a still day. Re-sealing without fixing the flashing lap just moves the problem a season down the road.
Usually not. A door that stops latching squarely at the marriage line is more often settlement at the foundation shims than a framing defect. Expansive clay soils along the Delta edge move with the seasons, and the marriage line is where that movement shows up first. The fix starts underneath, checking shims and level, not with planing the door.
Yes. Standard cabinetry and countertops work in a Dvele kitchen as long as the layout is planned around the factory mechanical positions. We work with KraftMaid cabinetry, Cambria, Silestone and Kohler fixtures, so you’re choosing from real, named products you can research yourself. A typical full kitchen remodel in Antioch runs an estimated $14,000 – $45,000, and the written estimate sets the final price. Call (866) 811-9694 to price yours.
Start with the fascia at the roofline and the downspouts at the module edges. Look for water tracking behind the fascia, gutters pooling against the edge, and staining at the seam where the assembled roofline meets the wall. Those signs point to drainage and flashing rather than shingles. Roof repair in Antioch typically runs an estimated $400 – $1800, and a full replacement an estimated $8,000 – $20,000. Call (866) 811-9694 for a free estimate.
Book Your Dvele Service in Antioch, CA
If you own a Dvele home in Antioch and need the site-side work done by people who understand module seams, marriage-line settlement and roof tie-ins, call (866) 811-9694. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free, quotes are written line by line, and the price is fixed once work starts.
Written by the team at Construction Antioch.